A customer installation picture

I love seeing how people install their secure bar holder kits.

I always sell more bar holder kits than I expect but it is VERY RARE that anyone ever sends me a picture of their final installation.

So today, a buyer sent me a picture of his installation. He left out the standard open bar holder which is JUST FINE. I put mine in because I wanted to have it support the 2×4 when the shed door is open.

It is a great installation. Thanks for sending!

Nice, neat & compact secure 2x4 bar holder INSTALLED!
Nice, neat & compact secure 2×4 bar holder INSTALLED!

Thanks for buying an Open Bar Holder

Had a nice order from Fort Collins CO today! Thank to the CSU Rams fan (an assumption).

The order was for 4 open bar holders which will look very sharp since they don’t have UGLY exposed screws like the ones you buy in Home Depot or Lowes.

I believe I have a superior design to what is available in the market an I’m 100% American made. I host my web site out of a Houston web hoster. I use wordpress which was designed partly in Houston. I live in Austin TX. They are manufactured in Hutto TX by a little metal working shop.

My customers are helping me “make America great again” by doing the simple act of trading together!

 

Add a Padlock locking tab to a secure 2×4 bar holder and shazzam…

Traditional 2x4 Bar Holder without ability to lock
Traditional 2×4 Bar Holder without ability to lock

When I first made my 2×4 bar holder setup with traditional 2×4 bar holders, I made about 3,000 trips to Lowes and Home Depot trying to find the right stuff (slight exaggeration).

Once I put a handle on my 2×4 bar and I had a nice setup for sliding the bar back and forth and removing, I discovered that there just seemed to be no good way to add something so simple as a padlock.

While a padlock won’t keep VERY determined crooks out of my shed – they could bring a circular saw or saws-all and get in – it would “up the ante” on difficulty at least. In fact if you want to think about security in the correct way, you have to assume it is a bit of a marginal returns versus marginal cost concept. In other words, the value of what you’re protecting must be at least worth the COST to criminals of going for it. If you think about an extreme case, the use of encryption causes crooks to have very expensive ‘cracking’ capability, both in computer hardware, time, and expertise. So the point is to make it hard enough that they’ll just move on to an area where they know the score is easier. That is all.

So here is a bulleted list of the escalation in security and the higher cost (equipment/speed) to break your security for a shed.

  • Standard shed hardware – Simple crowbar to bust and about 15 seconds.
  • 2×4 bar holder with some jerry rigged lock – electric screwdriver and about 2 minutes.
  • secure 2×4 bar holder with some jerry rigged lock – crowbar on the lock – 15 seconds.
  • secure 2×4 bar holder WITH special 2×4 bar holder with lock tab – circular saw on bar – 10 minutes + power source + noise risk.
  • NOT SOLD YET HERE (as of Dec 2016) – Steel 2×4 bar with Secure 2×4 bar holder kit – Now we are in blow torch territory!
  • etc.
  • etc.

So you see you can make each step harder and by adding a locking tab to the secure bar holder I can make the job quite a bit harder for a crook.

Here is my original closed bar holder drawing with a locking tab:

2x4 bar holder with padlock tab for high security
2×4 bar holder with padlock tab for high security

 

Here is the secure bar holder kit in action – without a padlock on m own shed. (I do wished I was a better carpenter).

Secure 2x4 Bar Holder Kit Raw Installed on my shed (poorly I might add)
Secure 2×4 Bar Holder Kit Raw Installed on my shed (poorly I might add)

Here is a gallery of my current designs using the secure locking tab:

How the SecureBarHolder Makes it harder to remove the bar

 

 

Old Style 2x4 Bar Holder Showing the Exposed Screws
Old Style 2×4 Bar Holder Showing the Exposed Screws

When I first decided I would use a 2×4 bar to close my shed instead of a combination of a latch and “something” to hold ONE of the doors closed, I went and bought “ordinary” 2×4 bar holders from Lowes or Home Depot (you can also get a traditional 2×4 closed bar holder or a traditional 2×4 open bar holder from Amazon (these are affiliate links)).

I was pretty happy with these for the most part except that  I only had a 2×4 to fasten the bar holders to. This meant I had to add extra wide wood pieces so that I could fasten to my shed. Since I did this “post shed construction” it looked like crap – even after I painted it.

I thought it would be really nice if there was a DIFFERENT kind of 2×4 bar holder which could be installed in only a 2×4 width. I couldn’t find one so then I designed one. Since there were both OPEN and CLOSED 2×4 bar holders in market I created a design for BOTH the open and closed in my compact (because it only takes a 2×4 width) and secure (because you can’t unscrew the screws with the bar in place) 2×4 holders.

Notice that since I have the screws UNDER the bar when it is installed you simply cannot use a screwdriver to remove the bar if the bar is in place. I had to create the holes in the front to get a screwdriver through. This is what makes my 2×4 bar holders so much better than the current bunch.

Here are the drawings which I made using only Apple Keynote to create. It was faster than using a 3D drawing program (at least for me).

Closed Small Compact 2x4 Bar Holder - Drawing & Dimensions
Closed Small Compact 2×4 Bar Holder – Drawing & Dimensions
Open Compact 2x4 Bar Holder - Mechanical Drawing Dimensions
Open Compact 2×4 Bar Holder – Mechanical Drawing Dimensions

I ended up with actual products that look like this below:

Find these innovative Bar Holders here!

Or Find them on Amazon here!

Or Find them on eBay here!